When riding, a bridle provides you with the ability to control the horse to a certain degree. Bridling can be hard at first, but it is actually quite easy to do. Part of successfully bridling a horse is to take care that the bridle does not cause discomfort to the horse. This article takes you through the steps required.
Note: This article demonstrates how to fit a full size bridle. Bridles generally come in three sizes: Pony, cob, and full size.
-
Prepare yourself by gathering the bridle. Put on your riding helmet at this stage for saf
-
3
Measure the bridle.
-
Begin by undoing the keepers on the bridle. Don’t undo all of them unless you are going to clean it. Only undo the cavison (part that straps on jaw) and the cheekpiece.
-
Place the appropriate sized bridle against the side of your horse’s head. This is to roughly assess the height of the bit and to make sure that when you do put the bridle on, it will not pull on his mouth and hurt him.
-
If the bit is too high, or too low, adjust the cheek straps to the approximate, correct height.
-
Place the bridle against his head once more.
-
-
4
Try the bridle on. Position yourself next to the horse’s shoulder on the near (left) side.
-
Hold the reins in your left hand and the headstall in your right hand. Slide the reins of the bridle over the horse’s head. Pass the bridle under the horse’s chin to rest on his nose. It helps to hold the cavison away to give the horse a better chance not to take the leather straps with the bit.
- Offer the bit. Lay the reins across the horse’s neck and put the bit mouthpiece in your left hand. Open the mouth by working your thumb into the corner of the mouth until he opens it – your goal is to apply some pressure downward on the mandible. One trick is to push the horse’s lip in under your thumb to protect your thumb from being bitten (horse may bite you, but won’t bite themselves). A horse may not accept the bit if it is very cold so try warming the bit in your hands first to make the bit more welcoming.
- Draw up the headstall. Take care not to click the metal bit mouthpiece on the horse’s teeth as you draw up the headstall.
- Place the headstall over the ears, gently pushing the ears into the ear loops and pulling away any forelock. Put the near ear under the headstall first, then the far ear. That way, if the near ear hurts and they pull away or act afraid in any way, you can walk to the other side of your horse and put that second ear through the headstall. This will help avoid your horse jerking away from the far ear and hitting you.
- It is best if you can do this without removing the halter until you are certain that your horse will accept a bridle being put on in place without being secured. Slip the halter off once the bridle is in place.
- Check the fit of the bridle as outlined in the following steps.
-
-
5
Measure the height of the bit. Open your horse’s mouth. The bit should be resting on the corners. If not, shorten the cheek pieces to the precise height.
-
Adjust the cheek piece on the other side as well, so that they are both level.
-
A good indication to show that you have correctly fitted the bit, is a wrinkle around the mouth, when he has it closed.
-
-
6
Measure the width of the bit.
-
Place a thumb on either side of the bit rings. There should be a thumb’s distance either side of the mouth.
-
-
7
Measure the throat latch. The throat latch strap is normally attached to the head piece. It is always done up on the left hand side. It should be loose.
-
Once fastened, you should be able to fit four fingers or a fist between the throat area and the lash. This is to make sure that there is no interference with the horse’s breathing.
-
-
8
Fit the caveson noseband.
-
The noseband should be at a height where you can fit two fingers under the projecting cheek bone. If it is too low, adjust the fastening to the correct height.
-
Check once more with your fingers. When the noseband is fastened, you should be able to fit two fingers inside. This allows the horse to relax his jaw when ridden.
-
-
9
Check the brow band. This should fit snugly around his head. It should never be too tight as this would pull the head piece forwards and pinch the horse’s ears. The brow band should not be too loose either – otherwise it could slip backwards.
-
10
Fit the reins. The reins should be the correct length for the size of your horse.
-
When you take up the rein contact, with your horse’s head in his normal ridden position, the spare ends should not interfere with the foot or stirrup. If the reins are too short, your horse cannot stretch and relax.
- Hold the reins in place while undoing the halter and removing it.
Tips -
- When you are buying a new bridle, it’s best to always have a few holes extra to be able to adjust shorter or longer as leather stretches in time. Or you may need to change the horses bit at some point.
- Horses tend to accept the bit more easily if they associate it with something good such as a treat or a good taste, so try putting some honey or rubbing a mint on the bit to help the horse accept it.
- When putting your finger in the horse’s mouth, push it towards the back where there are no teeth, so that the horse cannot bite you. When you press down, the cue will make him open his mouth.
- If you have a horse that is causing you trouble, for example, holding his head high, squeeze the base of his ears and he should lower his head. If he doesn’t, put your hand on the bridge of his nose, and behind the base of his ears, and shake his head gently and say “Down” firmly. He should respond.
Edit Warnings
- Horses can sometimes be unpredictable animals. If you are bridling one, you are dealing with its teeth, so take care.
- Do not let your reins lie on the ground, because if the horse steps over them, he could become quickly entangled, putting you and the horse in danger.
- Never tether a horse using a bridle. Leather is not strong enough to withstand a horse pulling against it and if the bridle snaps, the metal pieces on it can become dangerous.
- Try not to walk behind a horse, unless you are keeping a safe distance. When picking it’s hooves keep to the side of the horse.
Edit Things You’ll Need
- A safe, well mannered horse or pony
- A suitable bridle
- A halter and lead
- Boots
- Helmet